Nevada contractor license 0077896A · Advanced Design & Development, Inc.

Monday to Friday, 9:00 AM to 4:00 PM · 1155 Watson Way, Suite 7, Sparks, NV 89431

(775) 200-0648

How a shower is actually waterproofed, and why the tile is not the waterproofing

A tiled shower is waterproofed by a continuous layer under the tile, not by the tile or the grout: a pan sloped to the drain, a membrane (a waterproof sheet or coating) up the walls, and every seam and pipe sealed into it. That layer disappears the moment the tile goes on, so here is what it is, why grout is not it, and the one detail to ask any contractor to show you first.

Published
19 November 2026
Written by
Advanced Design And Development
Subject
What keeps a tiled shower from leaking
Applies to
New showers, and ones that already leak
Faster than reading
(775) 200-0648, Monday to Friday, 9:00 AM to 4:00 PM

01Why it matters

This is the assembly that fails where you cannot see it.

A shower that leaks rarely announces it. Water finds the gap in the waterproofing, runs into the framing or the subfloor (the layer of boards the finished floor sits on), and does its damage for months or years before a soft floor or a stain on the ceiling below gives it away. By then the fix is not regrouting. It is tearing the shower out, and often repairing what rotted underneath. That is why the waterproofing, not the tile, is where the care belongs, and why it is one of the three decisions in the guide to bathroom remodels.

02What it means

Waterproofing is a membrane, not the tile and grout.

Grout is cement: it holds water and lets it pass, and the tile around it is only as tight as the grout. The waterproofing is a separate, continuous layer underneath both: a shower pan sloped to the drain, a membrane up the walls, and sealed corners, seams and penetrations, meaning every place a pipe or a valve comes through the wall. Any water that gets past the tile meets a sealed basin and runs back to the drain. The tile is the wear surface. The membrane is the thing doing the job.

03The ask

Ask to see the pan and the membrane before you look at a tile sample.

A contractor who builds showers properly can tell you exactly how the pan is sloped, how the membrane laps (each piece overlapping the next so water runs over a seam, never into it), and how the corners and the niche are sealed. Many will flood test the pan, plugging the drain and leaving it filled with water to prove it holds, and photograph the result before a single tile goes on. A contractor who answers the waterproofing question with a tile brochure has told you where their attention is.

The same test works on the drain. A proper shower drain is built to bond to the membrane under a tiled floor, so water that gets through the tile still finds its way out. A generic fitting dropped in and grouted around collects only what runs across the surface.

04What goes wrong

Showers leak in four places, and every one of them is decided before the tile.

The curb, the low wall at the shower entry, where water concentrates and a thin or unsealed membrane gives out first. The niche, a hole cut into a wet wall that has to be waterproofed as carefully as the rest of it, and often is not. The bench, the same problem lying down: it is either sloped to drain or it holds water for good. And the drain connection, where the membrane has to tie into the drain so the water in the pan actually leaves. Each one is a detail settled before the tile and invisible after it.

Our own order of work, with the flood test we document before any tile is set, is in our bathroom remodeling work.

05Questions

Three questions we get about shower waterproofing.

No. Cement backer board, the cement sheet that tile is set on, is water resistant: it survives getting wet, but it lets water through. It needs a waterproof membrane over it or built into it. Backer board alone, tiled directly, is one of the common quiet failures.

Sometimes a surface reseal buys time, when the failure is at the glass or a fixture. When the water is getting past the waterproofing itself, resealing the surface does not reach the problem. On a walkthrough we can usually tell which one you have, and where we cannot without opening the wall, we say so, because selling you a reseal on a failed pan would only delay the real fix.

Not if it is built right. It just demands that the waterproofing be done right, because there is no curb to hold the water in. A curbless shower is a good test of a contractor, because it removes the margin a curb forgives.

06Keep going

Three pages for the rest of the bathroom.

07Start a conversation

Building or fixing a shower? Ask us how the pan gets built.

Send us the bathroom and the address, and we will walk the shower assembly with you, the pan, the membrane and the drain, before anyone talks about tile.

Fastest way to reach us (775) 200-0648

Monday to Friday, 9:00 AM to 4:00 PM. A person answers. The form goes to the same place, one business day behind the phone.

Optional. The phone is the faster path, since email replies can take a business day.
The address or at least the city, the rooms involved, and anything you already know about the house, such as roughly when it was built. That is enough to set up a walkthrough.
Optional. We ask because this site runs no tracking code.

By clicking Request a walkthrough, you authorize Advanced Design & Development, Inc. (Nevada contractor license 0077896A), and no other company, to contact you at the telephone number and email address you entered above, by telephone call and email, including calls delivered using an automatic telephone dialing system or an artificial or prerecorded voice, about the project you are asking us about on adadremodel.com. You are not required to agree to this in order to buy any product or service from us. See our Privacy Policy and Terms and Conditions.